展示会

平版印刷におけるインクと水のバランスの概念について

Oct 22, 2018 ご伝言

平版印刷におけるインクと水のバランスの概念について

我々は深セン中国の大きな印刷会社です。 我々は、すべての本の出版物、ハードカバー本の印刷、紙の本の印刷、ハードカバーのノート、sprial本の印刷、中綴じ本の印刷、小冊子の印刷、包装箱、カレンダー、PVCのすべての種類、製品のパンフレット、メモ、児童図書、ステッカー特別な紙のカラー印刷製品、ゲームカードなどの種類。

詳細はこちらをご覧ください。

http://www.joyful-printing.com。 ENGのみ

http://www.joyful-printing.net

http://www.joyful-printing.org

email:info@joyful-printing.net


1.はじめに


リソグラフィック・リソグラフィ・グラフ(オフセット)印刷は、A. Senefelderによって1797年に発明されたリソグラフィ撥インキ印刷方法に由来する。平版印刷および他のレリーフ、グラビア印刷およびスクリーン印刷は、異なる印刷パターンを生成するために使用される。 他の印刷方法は、印刷を作成して印刷物に転写するために1種類のフローインクのみを使用する。 平版印刷版は、プリントを生成するために2つの流体を使用しなければならない。 印刷(油)インクのみが版(水平版を除く)上の印刷物を識別できませんが、版を印刷するには水を塗布する必要があります。 パターンの一部は水の層で覆われ、印刷された部分は水を除去するために水溶性である。 インクが塗布されると、印刷された部分は油状で水分がないので、印刷されたグリース上にインクを流しやすくなる。 逆に、非印刷部分では、水がプレコートされているため、インク層が付着できず、グリース付きの印刷部分のみが残る。 印刷では、印刷インクはブランケットによって除去されるが、水の非印刷部分の一部もブランケットによって除去されるが、大部分のプリンタは製造中に印刷インクのみに注意を払う。 転写は、水の非印刷部分が転写され、印刷媒体の表面上に残っている水分の非印刷部分の効果に気付かないことにほとんど気づかず、印刷インク。 移転の困難。 平版印刷用水を慎重に分析すると、その効果はインクの転写を拒絶することであり、印刷媒体の非印刷部分から印刷媒体上の印刷媒体の表面に転写される水フィルム層は、印刷される印刷インキ。 付属すると、一部の部品が拒否されます。 十分に吸収された紙媒体がない限り、次のカラーインクの吸収のために、より乾燥した「乾燥」印刷面を有する。 したがって、1ユニット2色システムから1色ユニットへの現代の平版印刷機の設計があり、もはや2色1ユニットの設計は存在しない。


理論的には、リソグラフィは、印刷と非印刷を区別する効果を達成するために石油と水が混在しないという原則を使用すると誰もが言った。 実際、この議論には根拠がありますが、両方とも100%混在しているわけではありません。 しばしば、インクは給水システムにも移されるが、印刷インキ供給システム上のインキ層は、水平印刷がない限り多かれ少なかれ水を含む印刷版、ブランケットおよび紙印刷インキに移される。 インクの100%だけが水を含まないことが可能である。 その理由は、インクが妥協するために水分含有量との一定のパーセンテージを持たなければならないからです。 状況は、男性に女性エストロゲンがある限りです。 余りにも多くのエストロゲンがある場合、男性は明らかな女性的特徴を有する。 女性には男性ホルモンもありますが、それほど多くはありません。そうでなければ女の子は長いひげを持っています。 平版インキには、約5〜28%の乳化水を含まなければならない。 これは通常の現象であり、バッファリングに必要な安全ゾーンです。 北緯36度線のように、南北に沿って北と南の間には孤立があります。 非軍事緩衝液のように。 警察では、囚人を逮捕するには十分ではないことが多い。 警察は十分ではありません。 警察の目には「ネチズン」がなければならない。 制御が簡単です。 可能な内部から、その事件を解決するための手がかりを見つける必要があります。 さもなければ、公安の生態学的バランスを維持することは困難である。 。 平版印刷インキが100%の撥水性である場合、平版インキ平衡は、鋼製ケーブルの平衡と同じくらい容易である。 水が少しだけインクである限り、印刷部分は完全に除去される。 少量の非印刷部分がフルバージョンになります。 平版印刷の場合、インクバランス制御が容易である。 通常、平版インキの耐水性は18〜35%でなければならない。 これは印刷にはお勧めできません。 動作時には、耐湿限度を超えていれば、印刷時に印刷マーク上に多くの乳化白斑が発生するだけでなく、インクがなくなるまで崩壊するため、最大限の上限が使用される印刷インキローラと印刷版上では、印刷インキ転写機能の完全な崩壊状態は完全に失われている。 インク供給システムを洗浄して印刷する必要があります。


印刷機メーカーの中には、平版印刷をより容易にするために、水平方向の全面印刷を行った平版印刷版である水平無水オフセット法を用いて、プラスチックカードなどの小規模で小規模な印刷が行われているものもあるインク。 反発されたシリコーンゴム層は非印刷面として使用されるので、インクを塗布する際にシリコーン層の低口径材料の表面にインクが付着せず、印刷部分のみにインクが生成される。シリコーン。 添付された印刷物は、単一流体印刷方法に転写される。 温度が低すぎることによる印刷インキの貧弱な転写を避けるために、または非印刷インキの汚れの誤動作を避けるために、刷版およびインキ供給システムの温度を非常に正確に制御することだけが必要である温度が高すぎる。 また、一液印刷方式は横型印刷ではないので、インク液二流体印刷に支障はない。 1980年代には依然として多くの主張があります。 KBAは大きなCortinaフリー透かしを設計しました。 このマシンは、品質、操作性、迅速な印刷開始、そして無駄の少ない利点を持ち、新しい開発傾向があります。


インク供給・給水系の均一性


インク供給システム、水供給システム、インクタンクローラー、シンクローラー、プレートに最も近いプレート対向(接触)インクローラーまで、平版印刷機をインクバランスさせたい場合は、非常に平坦な直径およびローラーを有する。 円筒面の真円度、そうでなければこれらのローラの直径は不一致であり、ローラ表面に凹状欠陥がある。 最高の技術者が2つのシステムを調整したいとしても、それは不可能です。 直径が揃っていない限り、表面は凹面であり、表面は不均一であり、水は不均一であり、水は不均一であり、水は不均一である。 それは最も乾燥した場所でなければならず、不十分な水のために汚れていません。 濡れた場所が必要です。給水が多すぎて乳化を起こしやすいという問題です。 水分が少なくなると、水分不足による汚れが発生します。 ウォーターローラーの凹凸は、機械的なサイズだけでなく、インクまたはインク媒染剤(ファン・リーシュイ)に付着していると、部分的に水を含まない、または水を受け入れることができます。 下げる、状況は、水のローラーの壊れた表面と同じくらい良いです。 インキローラについても同様である。 直径が外形であり、真円度が良くなく、表面が壊れ、インクローラーの表面が親水性コロイドで染色されている。 濡れたときは、脱墨されます。 給水と同じですが、効果は逆です。 私は汚れることはできませんが、インクの色が薄くなり、インク供給領域全体でさえインクに大きな問題はありません。 インクや水のバランスは、均一性、表面欠陥、水やインク転写析出物等の付着がないことが重要な条件であり、スムーズな印刷が可能である。


ウォーター・ローラーとインキ・ローラーの適切な硬度と適切なローラー圧力の調整もまた、インキ・ローラー、ウォーター・ローラー、さらにはプリント・チューブを完全に使用するため、インキ・インキの転写にとって重要な要素ですインクを印刷して見てください。 接点の幅および幅は、ローラの圧力を調整するためのプレスの基準を決定するために使用される。 これは相対精度のみを持ちますが、絶対精度はありません。 相対精度とは何ですか? たとえば、5mmのタッチ幅が大きすぎます! 4mmまたは3mmに調整すると明るくなり、6mmは増えた接触になります。 しかし、ローラまたは印刷管の直径は異なっている。 接触振幅が同じであれば、圧力が同じであることを意味するものではない。 直径が2倍になると、接触圧力は同じになるように2倍にすべきである。 小径の場合も同様である。 計算する触手のサイズを小さくすることが適切であり、圧力を適切に生成することができ、あまり重くはない。 また、平版印刷機のゴムインキローラ及び印刷ローラは全て硬く柔らかく配置されており、押さえられたときには引き出し弾性体として軟質ゴムローラ又はブランケット付きゴムゴムチューブが用いられる。 したがって、これらのゴム弾性、ショア硬度値は、圧力、同じ大きな接触深さや接触振幅に影響を与える、硬いゴム★シリンダーは、より柔らかいゴムローラーやゴム、大きな圧力を生成します布と詰め物は、パッディング侵入圧力は0.05〜0.07mmの圧力のみを有し、中硬タイプは0.12〜0.15mmの圧力を有し、ソフトパッドは0.2〜0.3mmの侵襲に達することができる。 圧力がなければ、フルサイズのインク転写性が悪化する。 圧力の不足に関しては、水の移動が不十分でインクの移動が不十分であるため、異常なギャップの間を移動するために非常に厚い水層とインクが必要です。 当然のことながら、インクの供給と水の供給は本当に必要ありません。 水供給またはインク供給。 多量の厚膜インクを乳化させて異常生成を行うと、インク転写性が悪いだけでなく、印刷物への印刷が膨潤して乾燥が遅れ、バックプリントが発生し、インクの色が濃くなりドットが拡大します。 長い間、多くのインクローラーとウォーターローラーを使用するのが一般的です。 ローラゴムは材料の剥離によりスリム化し、インキローラとウォータローラの圧力が不十分であり、シャットダウン検査が必要です。 保存されていない廃版を印刷したら、4枚のタッチプレートインキローラーまたは1枚のウォーターローラーを下にしてプレートに寄りかかります。 少なくとも、レイアウトへの最後のパスの圧力を確認してください。 それは正常に保存することはできますか? 機械が停止した後、ローラの表面にある水平の接触残渣を確認するために、インチングを前方または逆に押してください。 それは一貫性があり、接触は中程度ですか? しかし、このようなローラータッチの内側は機能しません。 従って、印刷機の圧力を見るための圧接方式は、その都合の良い基準であるが、検査対象物の直径及び硬さが別の基準指標である。 インキローラの圧力が大きすぎると、接触幅が広すぎるため、インキ転移量が変化するだけでなく、軟化軟化してインキが容易にインキ供給量が低下する。 そのため、印刷版が傷つきやすくなり、ゴムの熱膨張性の肌が発生する。 損傷。


インキローラは、印刷インキが付着し、湿った水のコロイドによって容易に脱墨されないことを確実にするために、親油性ゴムを有していなければならない。 一方、ウォーターローラーはより柔らかい親水性ゴムを必要とする。 インキローラを親油性ゴムとして使用すると給水量が大幅に減少し、インキが給水量に影響を与えやすくなる。 もっと重要なことに、ウォーターローラーはそうではありません。 偶数のインクの下では、最低の給水ブロックに十分な水があるように水の量を増やす必要があるため、水のない領域は給水が多すぎます! 生成された領域の激しい乳化、水の供給の不均一、非平滑度は、ウォーターローラーの直径の変形以上である。


インキローラは、一般に、2つまたは3つの異なるゴム硬度グレードに分けられる。 インク溝ローラ部分とライドローラ付近のゴムは比較的硬く、約35°ショアであり、レイアウトのインキローラは柔らかく、インパクトストリークを低減します。 頭部は28〜30°ショアで滑らかで、他は30〜35°ショアの間にあります。 ウォーターローラーは、約18~22°のショアー硬度を有する軟質の親水性ゴムからなる。 水の供給は難しく、水の供給は圧力のために減少します。 現在、多くの製造業者がシンクローラをクロムからセラミック表面に変えている。 一方では、クロム酸化物の形成を避け、クロムローラーの親水性を妨げることができる。 一方、セラミックウォーターローラーは、良好で持続的な親水性を保持する。 これによれば、より環境に優しい目的を達成するために、IPAイソプロピルアルコールを減らすかまたは使用することさえ可能である。


3.温度制御と給水システムの添加剤


水は液体状態です。 それが熱を吸収し、分子摂動の臨界点に達した後、空気中の蒸気圧が小さいときに急速に空気中に逃げる。 反対に、水が同じ熱を吸収するが、空気中の蒸気は100%飽和に達する。 水は蒸気に変換して空気中に逃げることは困難です。 蒸発するにはより多くの熱が必要です。 この例から、インクと水のバランスにおいて、水の供給が同じであれば、空気中の湿度は低温では飽和に近く、水の蒸発は少なく、レイアウトはより多くの水。 逆に、空気中の高温、低湿度、低蒸気圧、および水のより速い蒸発は、不十分な水分をもたらし、平版印刷機の操作において水と水のバランスを大量に生じさせ、プレート上の水分大量の蒸発が不十分で、インクの非印刷部分に乾燥斑が生じます。 さらに、低温および高湿度のために、水の供給は過剰に乳化される。 白い紙に印刷すると、大量の紙になります。 それはまた、湿った水の消費を増加させるでしょう。 吸水性の少ない塗工紙、プラスチック、合成紙、金属箔であっても水を吸収しないものは、吸収時の水分の吸収がゼロで水分が多くなりすぎるため水分消費量が3つの側面。 1つはレイアウトのサイズ、温度と湿度、印刷速度、レイアウトのサイズが大きく、印刷速度が速く、水の消費量が増加に比例し、回転速度が速いのに対し、温度熱擾乱の蒸発を増加させることがあり、他方は熱擾乱の蒸発を増加させることがある。 その理由は、印刷速度を上げると(紙の比重は消費され、そこには乳化水が使用されているため)、紙が引き取る水の量と乳化したインクによって取り除かれる水の量が増加するからです多くの印刷ラインがあります)非印刷の白い紙の吸水性の増加による水の消費量の増加、増加)。 これらのインキローラの温度は、インキの粘性により上昇するか、ゴムローラを揺動させるインキローラによって熱が発生し、急激に温度が上昇してインキバランスが調整される。 一般に、平版印刷は大量の水分の蒸発のため熱の大部分を吸収するが、一般に25℃に適している。したがって、すべての印刷機は現在、水の蒸発を低減し、インクを保持するために湿潤水冷却システムを使用するシステムインクを供給する。 層は良好な渋みのため乳化を減少させる。 しかし、印刷機の速度が6~7000枚/時間から1時間当たり15,000枚、16,000枚、および18000枚になるにつれ、インク供給システムの温度安定性を維持することは不可能である。湿った水の低温。 現在、ほとんどの張家印刷機では中空スチールインキローラーを使用して冷却水をくりぬいてインク供給システムの温度を下げています。 温度が150℃を超えると、インクの硬度が軟化し、割れに対する耐性が低下します。 転写されるインクの量を減らすことは少なく、乳化が容易である。 これは、高速で長時間回転する印刷インクの色が軽くて軽い主な理由です。 インクの軟化により、中間調ドットが上昇し、制御を制御することができない。 ファーストプリントコールドマシンの通常の性能とは異なり、ドットポイントの増加によりミッドトーンは増加せず、完全な部分と暗い部分のインク濃度が低下します。 明かりの質は低下しています。 このため、横型印刷機だけでなく、横型印刷機も、ウォーターローラー方式に加えて、水槽内の水温制御を有しており、インキローラー方式では、インキローラーまたはインキツボローラーである。 センターは熱を吸収してインクローラーの温度を上昇させないようにします。


いくつかの酸およびコロイドを浴に添加しなければならない。 以前は、硝酸アンモニウム、リン酸アンモニウムまたは重クロム酸アンモニウムを使用していました。 これらの中でも、重クロム酸アンモニウムは水の酸性度を保つことができ、インクがアルカリ性になった後にインクがアルカリに変わることを回避する。 油は「鹸化」され、インクが分解して水に溶解し、脂肪および色素の汚染を引き起こす。 表面は二クロム酸塩を吸着し、容易に酸化され汚れない表面を形成する。 PS版が登場する前に、それは非常に有用な抗酸化、抗紙粉末摩擦表面であり、非印刷をきれいに保つのに極めて有効である。 PS版の初めに、アルミニウム板の表面は陽極酸化されなかった。 教科書の印刷で数千回転した後、アルミニウムは紙表面に過度のアルカリ性化学物質を吸収し、腐食を引き起こして印刷物が落ちる。 その後、陽極酸化処理を施した後、9度の高硬度耐摩耗性に加え、アルカリ化学腐食に対する耐性も大幅に向上しました。 従って、水タンク液の大部分は、主に4.5~5.5PHの酸性環境下に維持されるが、印刷用回転機はインクによって鹸化されないため、pH7以上の弱アルカリ環境下で製造される。 紙表面から溶解したアルカリ性物質の汚染に対抗するために、レイアウトの酸性度はインク収束を維持することができ、印刷は増加せず、酸性物質の添加は現在の親水性液体の重要な成分であるpH値はほとんど変化しない。pH緩衝液を浴に添加して、pHを4.5~5.5の正常pHに維持する。 したがって、真のPHデータは測定されず、ある程度の作用しか維持されない。 したがって、導電率は抵抗率によって検出される。 湿った水の真の酸含有量を知るために、もはや緩衝液の影響を受けない。 従来、印刷された紙の品質が悪い場合、アラビアガムの薄い層が印刷板上にあり、レイアウトおよび親水性を改善していた。 しかし、紙と紙粉が多すぎると、レイアウトが平滑化され失われてしまいます。 親水性で水和しているので、アラビアゴム層の消費を補うためにシンク液に含まれるコロイドに頼る必要があります。 PSプレートとCTPプレートはすべて硬化した酸素で処理されてアルミナを硬くするため、接着剤はほとんど添加されません。 フィルムは非常に耐磨耗性がありますので、現代のタンク液は親水処理液、界面活性剤、pHコントロールとバッファー、IPAイソプロパノールで構成されています。


今日、VOCの蒸発を避け環境に影響を与えるIPAを含まないアルコールフリーの湿式水システムが登場しましたが、IPAなしでどのように対処するのですか? まず、水中のカルシウム、マグネシウム、鉄、マンガンなどの鉱物をろ過して除去し、水分を軟化させ、湿度を高め、水分中の油分や汚染物質を除去する必要があります「純水」に近い良好な保湿力が常に維持されています。 UV光を用いて光触媒滅菌を行い、浮遊物や水分の発生を減らし、水道管の流動性に影響を与えたりブロックしたりする者もいます。 現在、アルコールを含まない雨水システムは、環境保護の需要の下での開発の方向性である流行にもあります。


4.印刷インキ供給層がインキ天秤の固定ドラムである


インクと水のバランスは、水層とインク層との間の相互作用であり、インク層の最小色を印刷して適切な色を印刷することができ、最も薄い水膜で印刷板を清潔に保ち、ファクター、これは最良のインクバランスです。 原則として。 しかし、実際の操作で一見簡単な操作条件は、新しい印刷機は、一般的にインクと水のバランスを達成するために簡単ですが、主な理由は、インキローラー、ウォーターローラー、フラットと丸みのそれぞれが非常に良いですゴムの弾力性は良好です。 請求。 そのため、左右のインク層の厚みが均一になり易く、インク層や水層が正確に転写され、インクの補充、水の添加、水の減少に反応する能力が期待通りに高速かつ正確である。 古い印刷機は、まずゴムが硬化し、膨れ、収縮し、圧力が不均一に変化します。 4つの印刷ローラであっても、印刷版には2つのインクしかなく、左右の圧力が均一ではなく、ゴーストやスジが発生し、インク層がうまく分散されていないために荒れてしまい、汚れ、色が十分なインクになるように厚いインク層を追加するのに十分ではないと同時に、インクのバランスを崩す。 1つのプレートウォーターローラーのみを備えた給水システムがより深刻な場合にも同じことが起こります。そのため、今日では多くの大型印刷機メーカーが以前の乳化インク構成に戻ります。 第1のインキローラは、水とインキを混合する方法である。 インクバランスの許容範囲と柔軟性を向上します。 したがって、3〜4ヶ月ごと(以前はゴムが以前より安定していました)には、ウォーターローラーとインキローラーの圧力チェックを調整する必要があります。 ウォーターローラーの滑らかな表面は、アルカリ性洗剤で除去する必要があります。 同様に、インキローラの表面は、インク中の媒染剤によって硬化することが多く、細孔が滑らかで滑らかであり、表面ゴムスエードの牽引力とインキ引き抜き能力が失われ、インクの分配性及びインク受容性が低下する。 より高度な、ウォーターローラーの第1と第2のレイアウトインキローラーに近く、上部のドライブハードスイングローラーには、表面がコロイドで付着されている場合、水分が多すぎるとセグメント親水性脱インキを生成することは容易です。 インク供給が極端に不均一になる。 この種の状況は、ウォーターローラーにおいてしばしば起こる。 インク層がセグメントに取り付けられている場合、インク遮断セクション内の水の量を得るためには、合計給水量を増加させなければならない。すなわち、最低および最低給水セクションの水は依然として利用できない。 不十分では、レイアウト上のインクスポットの発生がなくなりますが、水分が多すぎると、50%と100%を超えるものもあります。 インクタンクローラーには、セクション内のインク量を制御するインクボタンがあります。 逆に、ウォーターローラーには現在セクションコントロールボタンはなく、インキローラー部のみを吹き飛ばしてインキローラーの部分の乳化水を過剰の水として蒸発させる。 役割のバランス。 したがって、インクローラーとウォーターローラーとゴム表面の圧力は、それぞれの親油性、親水性、および弾性の丸みを保持し、これはセグメントおよび全体のインクバランスにさえ影響を与える。 特にプラテンインキローラの上にある印刷機の中にはギヤ駆動のインキローラ自体がありますが、クリーニングインキローラのインキスキージが表面のインキを加圧するため、長時間経過するとインキローラの直径が小さくなります摩耗するように、インキローラ表面速度が遅いですが、また、開く必要がありますインクの汚れのスジを引き起こす動作中に "ブレーキ"現象を引き起こす、版胴の表面の通常の速度を満たしていないゆっくり滑るのを減らす。 汚れは基本的なインクと洗濯のバランスにも影響しますので、硬いインクローラーを清掃する必要があります。


印刷機のウォーターローラーとインキローラーの通常の状態では、インクバランスについて簡単に話すことができます。 そうでなければ、異常な状況では、インクバランスは「アンバランスバランス」にある。 オペレーターは常に水に注意を払うべきですが、それほど注意を払うべきではありません。 水面の不十分な乾燥地点は発生しません。 今日の最新のCIP 3 / CIP 4は、情報の印刷されたインクマークセクションのプリプレスバージョン、元のジュース、印刷機の元の味は、印刷室の温度と湿度、さまざまなインクのプロパティのセットを持っている必要があります、紙、印刷圧力顧客の需要条件は、各色の色に変換され、各インクキー領域、この変換曲線は、各印刷会社、それぞれの印刷機、さらには各印刷機にも変わります。印刷機インク制御システムのコンピュータソフトウェアプラグイン上に配置され、最も適切な変換を行う。 印刷後、各インクキー領域のインク供給は、一貫した安定した連続的なインク供給を有するべきであり、過剰ではない。 インクキーを調整するためにプレート上のプリントの累積パーセンテージを視覚的に測定するために使用された以前のマスターよりも不十分であり、絶対的な利点と利点を有する。 しかし、インクスロットキーのゼロ復帰とレベリングが非常にうまく行なわれなければならないという前提があります。 それ以外の場合、Gaoming Technologyは一貫性のない出発点に基づいており、少量のインク供給領域、特にインクキーの5〜10%で簡単に変更できます。 エラーが発生すると、多くのデータが文字化けする可能性があります。 当初、インキツボキーの開き量はインキローラローラの回転角度に反比例するので、インキキーの平均開度は大きく、インキローラローラの回転量は比較的小さい。 逆にインキキーの平均開度は小さい。 インキローラインキの移送は比較的大きいので、インキキーの平均開度がゼロの印刷機では誤差値の干渉を減らすことができます。 以前のバージョンでは、インク供給システムの上部のインク層がインク層の厚さが異なるように、インクパターンが印刷パターンに従って分配されている。 また、次の印刷セクションの前に色を調整する必要があります。そうしないと、較正中の色の変更に影響します。 したがって、いくつかの印刷機はインテリジェントレベリング機能を有する。 このバージョンを10〜20の仮数を残して印刷すると、平均インク供給量の10%、15%など、インクタンクのキーが平均化されるため、インク消費量の多いインク集中領域比較的均等にバランスのとれたインク層が次の印刷に使用される。 インクの量が均一に印刷されると、インクの消費量は15%未満になります。 上記のインク供給層の凹凸を平坦化する必要はない。


グラビア印刷機とは異なり、インクの厚さやフレキソ印刷機、アニロックスローラーマイクロキャビティローラーを変更できない非常に固定された印刷機があります。 アニロックスローラーのインクの分布と深さによって、レイアウトのインク供給層の厚さが決まります。 また、インクタンクとインクタンクキーとの隙間から、凸版印刷と平版印刷をインク層から吐出されたインク層を5~7回転写して印刷版の表面にインクを形成するので、層がインキされる。 プリント密度に加えて、キーギャップによって形成されるインクの流れおよび印刷プレート自体の上のインク層の厚さも水供給を形成する。 それが印刷インキのバランスにおける重要な要因であり、きれいで適切な色の洗浄であり、インキ層と水供給層との間の比例関係は、絶え間なく作動することができないが、厚さの変化および温度変化インク供給系、さらにはインク殻が乾燥し、紙粉や紙毛が混入した場合に改善されます。 一方、給水の場合には、蒸発水の温度、ウォーターローラーの汚れの程度、pH値、印刷用紙の吸水率、空気中の湿度、そして水がどれくらい気化するか。 したがって、主にインクの供給量のために、インクと水のバランスの変化に影響を及ぼす多くの異なる要因が依然として存在する。


5.印刷中に湿った水が流れます。


ほとんどのプリンタや印刷会社の管理者は、大量の紙幣で購入したインクを管理するのに非常に注意を払っていますが、色再現性や印刷適性が優れているかどうかは重要ですが、ほとんど注意を払っていません。 水道水を多量の濡れた水とどこに流して使うのか。 水分除去:(1)紙の吸収は、材料によって異なる。 平滑なコート紙は、水分を吸収しない、雪の紙は第二に、光のコーティングされた紙はより多く、非塗装の紙はかなり大きい、そして多孔質ですティッシュペーパー上の接着剤がない、ニュースペーパーは、箔はほとんど水を吸収しません。 同種の紙では、高湿度そのものが比較的少ない水分を吸収し、低水分がより多くの水を吸収し、紙に吸収される水の総量は、印刷速度(印刷)に比例して増加する。 (2) Evaporation is a very important part of water consumption. The evaporation of the printing plate is closed due to the flatness of the lithographic printing machine, which makes the proportion decrease a lot. Instead, it is the blanket and the pressure. The cylinder surface has a non-printing part with water. The part is the larger part of the evaporation of water, especially the double diameter and triple diameter pressure. When there is no paper size, it will cause a larger percentage of water evaporation. (3) Evaporation of emulsified water in the ink layer of the ink roller is also indirect water evaporation. In addition to the evaporation of the printing area, the evaporation of the printing area will not increase due to the faster printing speed. The evaporation itself is closely related to the air pressure, wind disturbance, temperature and humidity of the printing machine room, which also causes the major factors of the balance of ink and water. Usually, the temperature is high, and the moisture of the natural moist water in the water roller, the emulsified water of the ink roller, the layout and other parts that are not printed to the surface of the tube will increase evaporation. High humidity will reduce the amount of water evaporation in all parts of the whole. Today, due to the cooling of the ink roller, the freezing and temperature control mode of the water supply system, and the temperature control of the printing machine room, the temperature changes little throughout the year. On the other hand, the humidity factor is often the cause of the printing machine room that is not easy to detect and less noticeable, but it often affects the water balance of the printing press. Many people mistakenly think that the air-conditioner installed with cooling is air-conditioning. A single tool that reduces the temperature of the printing room, sometimes removing excess water from the air. Real air conditioners should have four functions of cooling, warming in winter, dehumidification and humidification. Therefore, the functions of dehumidifiers and humidifiers are very important in air conditioning. It is not only necessary to cool down the air, but also hopes that the air conditioner will be under the action. In order to remove excess water, the room temperature is only 13 ° C in winter and the relative humidity is 90%. This is also a difficult printing condition, and the paper will be stretched and deformed. Therefore, it is not advisable to use the air-conditioner to dehumidify. It should be combined with a cold-discharge dehumidifier. It is not only dehumidification but also the function of improving room temperature. It is a good method. In summer, the air-cooling function has the function of cooling and dehumidifying one stone and two birds, keeping the humidity of the printing machine room stable, increasing the balance of printing ink and ink and the stability of printing quality. If the printing room is in the summer thunderstorm or rainy season, use a five or sixty-ton air conditioner to cool down, you can see that the water in the air is like a third of the water in the tap, because the water in the outside atmosphere, and two or three The four-color printing machine, the evaporation of water is in the spectrum of five or six hundred liters per day, so one day air-conditioner, removing 800~1,000 liters of water is nothing special. It can be seen that the humidity of the printing room is 50~60. % is more suitable in Taiwan, but in winter it is more suitable for 45~55%. Too much water consumption for printing presses will increase a lot.


Some people think that the faster the printing press, the more the water supply will increase, and some people think that the scale of the water supply on the printing press should be reduced. It sounds very contradictory, but each has its own statement and basis, and there is no conflict. Basically, the faster the printing machine speed, the more the printing quantity, regardless of the emulsification of the ink, the absorption of the paper, the increase of the temperature of the printing machine, the increase of the heat disturbance, and the increase of the amount of water used for evaporation is a fact. On the other hand, the water on the surface of the printing plate and the printing paper does not increase, so the speed is increased and the water demand is increased, but there is no proportional increase. If the water roller takes one water per print, Or take two waters, then the faster the printing speed, the more water will be taken, the equivalent consumption is OK, but in the evaporation of the consumption, the excess water will be redundant. On the other hand, if continuous water supply is used, the water is always sent to the humid system. If the ink emulsified water, paper absorption water and heat disturbance increase more water, it is necessary to use the speed of the fast water tank to increase some water supply, otherwise the water supply There will be insufficient, and how this program is written has different opinions.


6. lithographic plates, some causes


Ink and wet water are the main characters in lithography, and they play a dynamic blending role and role. But let us not forget that the more important thing is the "print plate". This piece can distribute and absorb water, and at the same time, it can absorb ink in the "printing part" where it is to be printed. This is a very important platform for water and ink to balance performance. 。


More than two hundred years ago, this platform was built on limestone in the Austrian Alps and the southern Alps of Germany. This milky white porous limestone plate has good water absorption. After accidentally dropping the candle, using a cloth with grease and water, when wiping, it was found that not only the wax was not wiped off, but the water and oil were separated from each other by the water and oil. It also promotes the principle of semi-physical and semi-chemical printing of non-printed and printed parts by lithographic printing in a single plane. Although there is a long time, there is also a very brilliant era of hand-painted color printing, hand-printed color lithography in Japan, Shanghai lithograph posters, and European and American lithograph posters, lithograph prints are still popular, but heavy stone plates can only be handmade and mechanical. Platform printing, can not enter the high-speed printing. In 1903, Mr. ZW Rubel of the United States invented the Zhangye lithography press, which is now indirect printing Offset, using a zinc metal lithography. The zinc lithographic material, its hydrophilicity and lipophilicity is almost in the middle, so the non-printed part of the printing plate is not very easy to get dirty, and the lipophilicity of the printed part is moderate, compared with copper. A lot worse. In addition, the zinc plate material is easily oxidized, and once it is oxidized, it becomes a non-hydrophilic and non-inking zinc oxide. This wall material, which is incompatible with printing, is placed on the non-printed portion to become a gray spot. In the printed part, the white spot on the imprinted part is full. Therefore, it is necessary to use more water to keep the non-printed part of the printing plate clean on the zinc plate. On the other hand, it is necessary to prevent the plate from being printed before the plate making. The zinc on the printing surface after plate making, printing, and preservation is oxidized. Zinc plate grain is thicker than aluminum and easy to wear, and it is also unfavorable for long-length printing. Now using aluminum plates, it has excellent effects in terms of hydrophilicity. In addition, although the grain grain (sand) is very fine, it is deep, and the water content is large, and the oxidation is formed under anodizing. Aluminum hardness is up to 9 degrees, higher than most gemstones, second only to diamonds, and the oxygen-polarized aluminum oxide layer has strong abrasion resistance, and more porous micro-structures, forming triple-type water-containing non-printing The pattern part, with less moist water, can make reasonable ink-and-wash balance printing, changing from zinc material to aluminum material as printing plate material, which is very helpful for lithography, easier to operate, not easy to get dirty, and aluminum is lighter than zinc. a lot of.


In the early days of the PS version in the 1970s, 3M Company also introduced un-ground aluminum plates, which were difficult to control the plate moisture, so it was not successful. Another multi-layer version for lithography is also a highly successful plate that can withstand millions of sheets for packaging and metal printing. The outermost layer of the multi-layer version is a highly hydrophilic chrome metal, which is used as a non-printed part, and the bottom is copper (red copper) which has very good lipophilicity. There are three layers in the production, some are made of steel as the base, the surface is first plated with copper, then chrome plated, the plate is printed with a flat plate in the form of a flat plate, and then the chrome layer is etched in the unexposed part until the lipophilic The copper layer is barely exposed. In the future printing, the chrome layer can absorb moisture, and the printed copper layer can absorb oil, forming a full-metal stable and high-efficiency printing plate, and the abrasion resistance is three or fifty times that of the general drying plate. Materials such as zinc and aluminum. The full version of the double-layer version is made of chrome-plated copper, but the plate is not resistant to mechanical impact. Therefore, the steel is a practical three-layer version, but it has never been introduced in Taiwan. Because the plate cost is high, the printing volume is not big enough. Enough to use such plates.


Nowadays, the PS plate and CTP plate are the mainstream plates produced by lithography. In the early PS plate, there are many difficulties. For example, the acid and alkali values of the printing paper are not resistant to paper, too acid and too alkali will fall off, so the moist water should be done. The change is due to the fact that the paper coating layer and the pulp filler chemical dissolved from the printing paper surface will be traced from the moisture of the rubber blanket surface to the printing plate, the water roller and the water supply tank to form a chemical accumulation. The printing pattern is corroded and not durable, so thousands of sheets can not be used. Therefore, it is effective to make the printing glaze, or to replace the sink liquid, clean the wet system, and replace the printing paper. I remember that when I printed the classmates in the factory, I printed three or four sets (manually loaded) every hour, and printed three or five hundred sheets each time. I used the water roller to wet and dissolve the glue on the plate for half a day. The printing pattern is not inked, mainly because the wet water glue is too much and the acid is too strong, so that the ink of the ink supply system loses a lot of oiliness due to too much glue mixed, so the manual washing is used to remove the glue, and the ink roller is cleaned. Water roller, re-printing to work smoothly. If the tank liquid tank has not been used for a long time, it will often ferment and grow mold, which is not conducive to the role of moist water.


In the non-printed part of the plate, it is necessary to apply glue before printing, so that a thin layer of arabic acid glue is attached to it, and the long-term water absorption of the colloidal molecules is exerted. Therefore, it is called lithography that is not only incompatible with ink. In addition to the principle, there are also many principles of meta-chemical action.


7.結論


An excellent lithographic press operator, today's technologically advanced era, although with many advanced precision machinery, motor to electronic equipment, under the control of many hardware and software, even the very difficult ink roller swing amplitude, pendulum phase, You can make fine-tuning change control on the console. Others such as the turning mechanism, the front and rear printing presses, the phase change of the cylinder and the jaws are opened and closed by the normal paper, and the twisting and turning back to the tail of the paper is extremely accurate. The complicated control work can be done by modern printing presses, not to mention the size of CIP 3 /CIP 4, ink key information reception and pre-adjustment. Therefore, Manroland changed the pad printing machine to press only one Start button, and all the projects were executed under the programmed system. But the advantage of our lithographic printing press, the use of thin low-cost aluminum, and high-precision 2400dpi, 3000dpi high-precision CTP platesetter, can make a plate from 500mm to 2860mm, both have good overprint precision, the plate from Enter to install fully automated.


The printing machine works for four or fifty years, and I want to find ways to develop the water film thickness of the wet water on the printing plate. According to the visual observation of the previous teacher, it is estimated that the amount of moisture on the non-printed surface of the printing plate is determined by the gloss of the side of the printing plate at an angle of about 10°, and it is easier to match the printed surface of the printed plate. Lose water in the block, do monitoring and add water. In this area, the prints are kept clean, and the total water supply is reduced. If the water is tested, the dry spots will appear immediately, indicating that the water supply has reached the critical point of the lower limit of the danger zone. It is not easy to raise the water supply higher. Produce defective products. The masters often have to change depending on the weather. At noon and afternoon, the temperature is high and the water is raining. When the wind blows over the window, the printing plate will dry up near the window, and quickly sprinkle water to make up the water, so these people's experience, Observing, in conjunction with the slower and slower production rhythm at the time, it is feasible to control the monochrome machine and the two-color machine, because these have a deep understanding of the ink and water balance characteristics of each environment and various blocks of the machine and the countermeasures are formed. A "work" that can be produced. Today, Zhang Yeping Printing Machine is not only four colors, six colors, even eight colors and ten colors. It is not only impossible to use manual inspection to visually check the water film of each printing plate on the tube, and the printing machine is now entering. In a small number of diverse production environments, it is not allowed to use manual observation of the water supply of various color plates. Instead, it is based on the speculation of workers, which is a large cover for high-priced, high-productivity flat printing machines worth tens of millions and hundreds of millions. The door is also a very ironic thing. The normal printed sheet was printed in the last minute. After 250 or 550 sheets in the next minute, it was a pile of waste prints that were too dry and too wet! This very drastic change does not exist in high-speed gravure and flexo press production. Therefore, using optical technology, infrared measuring instruments, microwave reflection and other technologies, I want to measure the research and development technology of the water film thickness of each block on the lithographic printing plate. Although there are so many high-tech measurement procedures, there is still no one today. , the work into practical control. Even with the Anilox Roller micro-acupressure ink supply roller, there is a more uniform ink supply layer printing method, but there is no successful control of the ink balance, but special ink must be used for normal printing. It can be seen that this difficult picture of ink and water balance is still based on the experience of high-tech lithographic printing presses. This is the operation of hundreds of thousands of printing presses. Every day, it is enough to do enough to operate the production. High-quality products, high-yield prints, this is a fact and a very helpless thing. Therefore, we should adjust the water supply, ink supply and roller elasticity, precision, pressure and surface condition of the printing machine, and then improve the ink and water conditions of the printing plate, and control the temperature and humidity of the printing machine room, ink and consumables. The quality management, coupled with the CIP 4 data, believes that under the helpless conditions, perhaps we still have to use lithography to continue printing for another 50 years, a hundred years is not necessarily, this ink and wash balance struggle history will continue to write Go on.

お問い合わせを送る